Log in
DoItYourself.com Community Forums> Interior Improvement Center>Carpentry, Cabinetry and Interior Woodworking
>
New Posts
Today's Posts
FAQ
Community
- Member List
Forum Actions
- Mark Forums Read
Quick Links
- View Forum Leaders
Search
Room conversion
Subscribe to this Thread
Thread Tools
Search this Thread
Tolyn Ironhand
Group Moderator
Join Date: Nov 2007
Location: United States
Posts: 14,428
Upvotes: 72
Received 899 Upvoteson760 Posts
It is up to you what you want for wall covering. Drywall is cheap but requires finishing if you want the walls to be seamless. Plywood requires minimal finishing but you will have seams. You could also do beadboard plywood sheets or even shiplap. It all depends on the look you want.
Upvote
B
beelzebob
Member
Join Date: Oct 2015
Location: Ct.,USA
Posts: 3,324
Upvotes: 31
Received 314 Upvoteson277 Posts
The photo of the wall with the door open shows the 2x4 studs have the 4 inch side parallel to sheathing rather than perpendicular to sheathing making it easier for this wall to bow in/out as more weight is added, especially if adding finish material to the inside roof area. This is further aggravated by the fact there is nothing tying the side walls together. This room can't be part of a house! Is there a permit involved?
Upvote
the_tow_guy
Group Moderator
Join Date: Feb 2001
Location: SW Fla USA
Posts: 12,278
Upvotes: 108
Received 262 Upvoteson213 Posts
Ireland apparently. Good eye, Ironman.
Upvote
Related Articles
Conversions to Create Handicap Vans By Joy L.
Toilet Bidet Conversion Kits By Sarah Peel
Planning for a Tub to Shower Conversion By Brandi Grays
Lighting Your Home Room by Room By Amy Jensen
$Trending
Cost to replace a deck
17 replies 180 views
Opaque deck stain failure, looking for options
11 replies 125 views
Chasing an air leak in a feeezer
9 replies 89 views
Haier window air conditioner
8 replies 114 views
What size flex conduit for 20A pop-up kitchen island receptacle?
6 replies 97 views
Is this something I need to worry about it?
5 replies 103 views
Rheem rtex 11 in container house question
6 replies 122 views
Failed Proflo 32 Gallon pressure tank need some advice please
12 replies 362 views
Installing icemaker in LG fridge
4 replies 82 views
Tuning system - eliminated one vent
4 replies 70 views
CHECK OUT SIMILAR POSTS
-
Carpentry, Cabinetry and Interior Woodworking
B
beowulf on May 25, 2024
Hi all.I am sure many have worked on or had experience with water leaks below kitchen sink into the cabinet area. We waited way too many years to try to solve this problem and our sink separated from granite so in trying to fix this, ended up punching through the floorboard which is saturated/moldy/etc. So I figure.. I can fix it. In removing the floorboard today, I now see there is mold all along the cabinet framing.. its soggy, very wobbly and I could easily pull the stuff apart. I suspect right behind the cabinet, which is a wall of sheetrock that leads to the other side of counter where we have 4 stools for sitting at, so a wall/barrier I guess, that some of that may be messed up too.I am a little leery of trying to remove the cabinet completely from under the sink. To the left (looking at it/sink) is the dishwasher, and to the right is a broken trash compactor that we use for garbage still just doesn't compact. Would there be a way I could "replace" the back bit of cross (left to right bottom) if I remove that, and then reinforce the front to back sides (left and right), with 2x4 or 1x4 maybe.. that would sit along the cement bottom? There is a 2x4 brace in the middle that goes front to back. My concern though is not so much as fitting something there but how to attach it to the cabinet. The cabinet is clearly crappy particle board build. Clearly super cheap crap cabinets. Honestly if I were going to live here for a while long I'd consider removing the granite top, and rebuilding the cabinets myself with better quality wood, and somehow waterproofing (if possible.. treated I Think) the wood, etc. But that is probably way more work than I could do and not even sure if its more for advanced people or is it literally just remove the glue/etc from bottom of granite.. carefully remove granite counter top (which is about 4 feet by 8 feet in size give or take). But if that is a better way to go, I'd rather do that and replace the cabinets.. though to be fair, the full kitchen is same cabinets so not sure if I built my own and it wouldn't match the rest of the kitchen how bad that is for resale value. Don't have a clue how I would find the same cabinets to replace them though. Read More